Name: milKit Conversion Kit
Brand: milKit

milKit makes tubeless conversion a breeze! This is your one stop shop for converting your mountain bike or road bike to tubeless tires. Running a tubeless set up has many advantages: it is lighter, more resistant to pinch flats, has better traction and avoids ride stopping punctures from thorns and sharp stones. However, before milKit revolutionized tubeless mounting, getting your wheels set up was a long messy job. Checking sealant levels was equally tiresome, so many riders ran the risk of riding without sealant as checks meant more mess!

milKit has made this easy:

Install rim tape

Install milKit valves and screw out the milKit valve core

Pre-inflate your tire up to 22 psi (we recommend the milKit Booster) – the rubber valve flaps ensure no air is lost even without the valve core installed

Measure out the correct amount of sealant and insert into pressurized tire using the syringe: mess-free!

Screw the valve core back in and inflate the tire to full riding pressure – the tire now jumps onto the rim fully. You’re ready to ride!

Ongoing maintenance is also easy. With other tubeless tire systems you need to remove the tire to check if enough sealant remains, with milKit you can simply remove the valve core and insert the syringe to check. No mess and faster results!

The syringe holds 60ml or 2 oz of fluid and comes with a flexible connector and a large needle to push through the valve and rubber flaps. There’s also a sealant regulator that screws into the syringe for easy refilling. The needle has an angled end for effective removal of all sealant in the tire so you know exactly how much sealant is in there.

Rubber flaps at the bottom of the valve prevent sealant from filling and blocking the valve, as well as ensuring no air is lost when the core is removed.

milKit sealant is thicker than others and always stays a consistent homogenous liquid. There is no need to shake it before use. In the tire, the milKit sealant does not decompose into rubber particles and an aqueous residue, but it dries evenly and slowly and therefore remains effective longer than comparable products.

milKit sealant’s microfibers give it a strong puncture sealing capability, with results for tears of up to 6mm. It covers the inside of the tire evenly, and adheres better to the tire wall than thin latex products, so the all-important microfibers are distributed optimally and ready to act as soon as you puncture.

The conversion kit contains everything you need to convert to tubeless:

milKit valves with rubber flaps that ensure clean and easy setup and maintenance
milKit compact syringe to measure and refill sealant through the milKit valves
milKit tubeless sealant that stays effective longer and repairs bigger tears
Rim tape needed to convert your wheels to tubeless
1x milKit sealant bottle 250 ml / 8 oz
1x milKit compact syringe system
2x 45 mm milKit tubeless valves
1x 10m/11yd roll of milKit tubeless rim tape 21, 25, 29, 32 or 35mm/0.82in
1x additional needle for syringe filling
1x valve core tool

Occasionally, without notice, manufacturers change product design and/or specifications.

Tubeless Sealant and Accessories Guide

Riding with tubeless tyres means that you’ll spend less time fixing flats and more time shredding the trails or lighting up the open road. In this tubeless guide we’ll look at all the things you need to get your wheels and tyres rolling without inner tubes.

Tubeless Sealant

Sealing all the little air gaps in your tyres, whether through a puncture or a less-than-perfect tyre/rim seal, tubeless sealant is an essential for every cyclist who wants to ride without tubes. There are a few different options to choose from, but they all work on the same principle: a liquid that solidifies when it leaks out of the tyre to seal gaps and punctures.

While simple latex-based liquids will work as sealants most brands sealants use special formulas and additives to improve longevity and sealing performance. Sealants with particles added are better at sealing larger holes so are ideally suited to mountain bike tyres. Lighter weight sealants are good for road bikes as puncture holes are generally smaller and easier to heal. Some sealants don’t work well with CO2, so check for compatibility if you plan on using a CO2 inflator to seat your tyre.

How much sealant should I use?

The amount of sealant you need to use will depend on the volume of the tyre. Brands will recommend specific amounts for their sealants which will be about 30 – 60ml for road bike tyres and 70 – 150ml for MTB tyres.

The table opposite shows typical sealant quantity recommendations to use as a starting point. If your tyres are a little porous some sealant may leak out. Don’t worry about this, it’s just the sealant doing its job, but you may need to top up with a little extra to be sure that there is enough left to seal any punctures.

Tyre size	Sealant quantity
27.5 x 2.0	75ml
27.5 x 2.4	110ml
29 x 2.0	90ml
29 x 2.4	130ml
700 x 25	30ml
700 x 32	50ml

Tubeless Sealant Accessories

Tubeless Rim Tape

If your wheel doesn’t have tubeless ready rim tape installed, then you will need to tape the rim with tubeless compatible tape. Tape is available in different widths and you’ll need a size that best matches the internal width of your rim.

applying tubeless rimn tape to an mtb wheel

Tubeless Valves

As there is no inner tube the valve attaches directly to the rim of a tubeless wheel. These are usually Presta valves. Make sure that you get ones that are long enough to easily go through the rim of your bike. Longer valves are available for deep section rims. The valve cores tend to block up with sealant after a while so they will need taking out and cleaning and/or replacing from time to time.

Tubeless Conversion Kits

Tubeless conversion kits contain sealant, tape and valves as well as fitting instructions, so these are the best option when converting your wheels for the first time. When buying a conversion kit make sure that you get one with the correct tape width and valve length to fit your wheel.

Sealant Injector

You can pour sealant into the tyre before you finish putting the tyre on, but many people prefer to inject the sealant through the valve. You can use a normal syringe, but specific injectors usually include a valve adaptor that makes the job easier. Some Tubeless Kits include an injector.

injecting sealant into a mountainbike tyre

Tubeless Tyre Repair Kits

While sealant will heal smaller punctures by itself a larger hole or tear in the tyre will need to be plugged or patched. Tubeless plug systems offer long lasting repairs and are very quick and easy to use even at the road or trail side. If you don’t want to have a small bit of the rubber bung showing through your tyre, then you will need to take the tyre off and patch it from the inside.

repairing a puncture in a tubeless mtb tyre

Tyre Inserts

Foam tyre inserts cushion the blows from rock strikes, especially when running low tyre pressures. They are a great way to protect your MTB tyre and rim when riding through rough terrain. Inserts can also help to keep the tyre on the rim more securely to avoid burping air when cornering.

Tubeless Inflators

When you fit a new tubeless tyre, it can sometimes be difficult to get the tyre seated properly on the rim. This is because a normal track pump doesn’t blow the air out quick enough to overcome the initial gaps between tyre and rim. Tubeless inflators allow you to blast a shot of air directly into the tyre to pop it onto the rim.

Tubeless inflators like the original Air Shot need to be pumped up with a separate track pump whereas others combine both track pump and inflator tank. See our range of tubeless inflators

How to Convert to Tubeless

While tubeless systems will save you time in the long run, they do take a little more care to set up.

See our Tubeless Tyre Conversion Guide for more.

2025 Gravel Bikes

milKit Conversion Kit